1 000 kr
![5.5inch HDMI AMOLED touch, for alt men beregnet for raspberry pi. Bare å gi bud.](https://images.finncdn.no/dynamic/480x480c//2024/8/vertical-0/25/9/367/566/159_13a9a659-8d29-4352-a623-2872c91f6196.jpg)
Tilstand: Ny
Ny i forseglet antistatisk pose. Med SD-kort-slott. Kan sendes som brev.
Kan brukes med Esphome og home assistant.
Fra leverandør:
ESP32 er en kraftig mikrokontroller som gir en enkel og effektiv måte å koble sammen smarte enheter og kontrollere hjemmeautomatisering. Med sin høye ytelse og lave kostnad har ESP32 blitt en favoritt blant utviklere over hele verden. På Elkim finner du et bredt utvalg av ESP32-modeller, inkludert utviklingskort og spesielle enheter som er utviklet for å koble sammen kameraer og andre bildesensorer med ESP32. Med ESP32 kan du programmere enheter for å utføre forskjellige funksjoner som å styre lys, overvåke temperatur og fuktighet, og mye mer.
BESKRIVELSE
Mini overvåkningskamera med ansiktsgjenkjenning. Støtter Arduino IDE. Les mer om hvordan man kan legge til rette for dette her:
Det finnes mange forskjellige prosjekter, og måter å bruke ESP32-CAM på.
1. ESP32-CAM is a WIFI+ bluetooth dual-mode development board that uses PCB on-board antennas and cores based on ESP32 chips. It can work independently as a minimum system.
2. ESP integrates WiFi, traditional bluetooth and BLE Beacon, with 2 high-performance 32-bit LX6 CPUs, 7-stage pipeline architecture, main frequency adjustment range 80MHz to 240MHz, on-chip sensor, Hall sensor, temperature sensor, etc.
3. Fully compliant with WiFi 802.11b/g/n/e/i and bluetooth 4.2 standards, it can be used as a master mode to build an independent network controller, or as a slave to other host MCUs to add networking capabilities to existing devices.
4. ESP32-CAM can be widely used in various IoT applications. It is suitable for home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals and other IoT applications. It is an ideal solution for IoT applications.
Features:
– Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
– Low-power dual-core 32-bit CPU for application processors
– Up to 240MHz, up to 600 DMIPS
– 2M PSRAM
– Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
– Support OV2640 and OV7670 cameras with built-in flash
– Support for images WiFI upload
-Support TF card
– Support multiple sleep modes
– Embedded Lwip and FreeRTOS
– Support STA/AP/STA+AP working mode
– Support Smart Config/AirKiss One-click distribution network
– Support for serial local upgrade and remote firmware upgrade (FOTA)
– Support secondary development
Note:
This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately.
Package Included:
1 x ESP32-CAM Module
1 x Camera Module OV2640 2MP
Module modelESP32-CAMPackageDIP-16Size27*40.5*4.5(±0.2)mmSPI Flashdefault 32MbitRAMinternal520KB+external 2M PSRAMbluetoothbluetooth4.2BR/EDR and BLE standardsWi-Fi802.11 b/g/n/e/iSupport interfaceUART, SPI, I2C, PWMSupport TF cardMaximum support 4GIO port9Serial port ratedefault 115200 bpsImage output formatJPEG (only supported by OV2640), BMP, GRAYSCALESpectrum range2412 ~ 2484MHzAntenna formonboard PCB antenna , gain 2dBiTransmit power802.11b: 17±2 dBm (11Mbps)
802.11g: 14±2 dBm (54Mbps)
802.11n: 13±2 dBm (MCS7)Receiving sensitivityCCK, 1 Mbps : -90dBm
CCK, 11 Mbps: -85dBm
6 Mbps (1/2 BPSK): -88dBm
54 Mbps (3/4 64-QAM): -70dBm
MCS7 (65 Mbps, 72.2 Mbps): -67dBmPower consumptionTurn off the flash: 180mA at 5V
Turn on the flash and adjust the brightness to the maximum: 310mA at 5V
Deep-sleep: The lowest power consumption can reach 6mA at 5V
Moderm-sleep: up to 20mA 5V
Light-sleep: up to 6.7mA 5VSecurityWPA/WPA2/WPA2-Enterprise/WPSPower supply range5VOperating temperature-20 °C ~ 85 °CStorage environment-40 °C ~ 90 °C, < 90%RH
Du må være logget inn for å se brukerprofiler og sende meldinger
Logg innSist endret: 1.8.2024, 16:08 ・ FINN-kode: 339673031
Betalt plassering