Recapitation Guitars, Steel Falcon Series

All guitars 23000 kr. Custom made in Sykkylven Norway by guitar builder, recording artist and producer Jamie Rust of Recapitation Guitars & Egregore Records and Production. Open for repairs setups, string change and music production. Contact re-capitation.com for your guitar and music need. If you would like to carry my guitars in your shop get in contact.

Guitar 1 Steel Falcon 333B

Built from choice recovered maple hardwood. This all-original design has a 25-1/2” scale maple neck with a rosewood fretboard, 24 Jescar jumbo gold EVO frets with skull and cross bone inlays. The nut is a Graph tech Black TUSQ. This fine axe has a double action truss rod, custom carbon fiber truss rod cover and black gloss Gotoh tuners. This guitar is finished to have a rugged appearance but not reliced. This is a 2-part epoxy finish that resonates well with the maple wood body and neck . The neck is a large round C taper. This neck has a 12″ radius with neck through body construction, maple neck and sides. The body has a slight upper arm contour that feel good on the arm. All electronics are shielded with copper shielding tape. The pickups are Kent Armstrong M213k in the neck position at 7.79 k and M215k in the bridge position at 12.44 k. The two humbuckers are controlled by two 500k Bourn mini pots. Blending the two or turning on and off is how sound caricaturists are sculpted, along with the on on on mini switch. The down position on the the mini switch is both pickups in humbucking mod with massive sustain. The middle position puts the pickups out of phase for a quaking tone and the switch all the way up puts both pickups into single-coil mode for a more Tele sound. The 500k mini Bourn tone pot with a Sprague Orange Drop cap, 0.033, controls both pickups. This guitar is also quipped with a Tesi Switch for the strobe affect and the option to mute when plugging in or out of a hot cable. This axe has a custom made jack plate with a switchcraft jack. The Gotoh 510UB stopbar bridge is adjusted tight to the body creating massive sustain, while being in a fast low playing spec of 1.30 mm on low E and 1.00 mm on the high E at the 12th fret, an adjustment was recently made removing some of the finish under the footprint of the bridge to achieve this low fast playing adjustment, this is only noticeable on the back side of the bridge, it also aids in string replacement. The guitar comes with 3 bridge adjusting tools. The largest wrench sets the height, the smallest also goes down into the height adjustment hole to lock things tight. The medium size wrench adjusts foreword and back positioning of bridge. The guitar can be set up higher if need be. Guitar comes with Dunlop strap lock buttons. These buttons can be used with the locking system or with out. Electronics all held in place with a carbon fiber control plate. The pick guard is also made from real carbon fiber that ads to the resonance and sustain. This guitar is the first of this model. This guitar is 42 inches or 107 cm long and weighs 3.30kg or 6.6 lb. Comes with a light wait easy to carry Gator case. Remember, save a tree and buy from builders recovering hard woods.

Guitar 2 Steel Falcon 333

Built from choice recovered maple hardwood. This all-original design has a 25-1/2” scale maple neck with a rosewood fretboard, 24 Jescar jumbo gold EVO frets with skull and cross bone inlays. This fine axe has a double action truss rod, custom carbon fiber truss rod cover and black gloss Gotoh tuners. A custom carbon fiber head-stock back plate provides added resonance + stability. It looks awesome with its matching pickgaurd and control plate.

This guitar is finished to have a rugged appearance, as to fit with the mojo of the axes cooled forged steel patina look. This is a 2-part art epoxy finish that is impervious to UV and solvents of all types and wont yellow. The finish on this axe is meant to be rough, giving it a semi relic appeal.

The neck feels like a medium C taper. This neck has a 12″ radius, with neck through body construction and a bone nut. Maple neck and sides. The body has an upper arm contour that shows off some of the wood grain.

All electronics are shielded with copper shielding tape. The pickups are Kent Armstrong M213k in the neck position and M215k in the bridge position controlled with a 3-way toggle, Bourn 500k mini pots and a Sprague Orange Drop cap, 0.033, black gloss knobs and switch craft jack. Push/pull coil split on tone knob. It has a Gotoh tuneomatic bridge and a Gotoh stop bar. Comes with Dunlop strap lock system. Electronics all held in place with a carbon fiber pick guard and control plate, that ads to the resonance and looks awesome.

This axe is amazing and ready to rock! This guitar is #001 in a series of 4 guitars that will be made. While they will all be similar, every guitar will have its own uniqueness and mojo. This guitar is 41 inches long and weighs 6.8 lb. Comes with a new, lite weight highly protective and easy to carry Gator case. Remember, save a tree and buy from builders recovering hard woods.

Guitar 3, Steel Falcon III

This all-original design has a 25-1/2” scale maple neck with a rosewood fretboard, 24 Jescar jumbo gold EVO frets with skull and cross bone inlays.

The nut is a Graph tech Black TUSQ. This fine axe has a double action truss rod, custom carbon fiber truss rod cover and black gloss Gotoh tuners. The face of the headstock still has the original U.S. stamp indicating it was kiln dried. This is just a fun touch left over from its former life.

This guitar is finished to have a rugged appearance as to fit with the mojo of the axes cooled forged steel patina look. This is a 2-part art epoxy finish that is impervious to UV and solvents of all types, and wont yellow. The finish on this axe is meant to be rough, giving it a semi relic appeal. The neck is a medium taper with relief set at 0.12 at the 5th fret. This neck has a 12″ radius with neck through body construction, Maple neck and sides. The body has an upper arm contour that shows some of the wood gain off.

All electronics are shielded with copper shielding tape. The pickups are Kent Armstrong M213k in the neck position and M215k in the bridge position controlled with a 3-way toggle, WD 500k mini pots and a Sprague Orange Drop cap, 0.033, black gloss knobs and switch craft jack. It has a Gotoh tuneomatic bridge and a Gotoh stop bar. Comes with Dunlop strap lock buttons.

Electronics all held in place with a carbon fiber pick guard that ads to the resonance. This thing sings!

This guitar is a prototype and there will be others similar, but this is a one of a kind that future axes may be built from some of the specs.

This guitar is 45.5 inches long and weighs 8.0 lb. Comes with a light wait easy to carry Gator case. Remember, save a tree and buy from builders recovering hard woods. This guitar is in “Norway”. The single Akin to Running was recorded with this guitar.

Returnable within 30 days of delivery in Norway. Buyer pays for return shipping and a Kr 1500 handling fee.

Guitar 4, Steel Falcon II

This guitar is not yet pictured here but is similar to STF III

Built from choice recovered hard woods, maple and red ash. “This guitar has been updated with new nickel silver frets and large side dots. some of the older side dots are still visible. This is a semi relic finish, so there is a bit of finish missing where the fret-board and neck meet. The longer horn on the bottom that you see in some of the photos has been evened out so the guitar can stand when leaned. This guitar was made in 2019. re-capitation.com

This all-original design has a 25-1/2” scale maple neck with a rosewood fretboard, 24 jumbo nickel silver frets with skull and cross bone inlays.

The nut is a Graph tech Black TUSQ. This fine axe has a double action truss rod, custom carbon fiber truss rod cover and black gloss Goto tuners. The black gloss string tree is also used to hold the cover in place.

The face of the headstock still has the original U.S. stamp indicating the wood was kiln dried. This is just a fun touch left over from its former life.

This guitar is finished to have a rugged appearance as to fit with the mojo of the axes cooled forged steel patina look. This is a 2-part art epoxy finish that is impervious to UV and solvents of all types and wont yellow. The finish on this axe is meant to be rough, giving it a semi relic appeal.

The neck is a slim taper and has a 12″ radius. This is a neck through body construction, Maple neck with red ash sides.

The body has an upper arm contour that shows some of the wood gain off.

All electronics are shielded with copper shielding tape. The pickups are Gibson Burst Bucker Pro’s controlled with a 3-way toggle, WD 500k mini pots and a Sprague Orange Drop cap, 0.033, black gloss knobs and switch craft jack. It has a Goto tuneomatic bridge and a Goto stop bar. Comes with Dunlop strap lock buttons.

Electronics all held in place with a carbon fiber pick guard that ads to the resonance. This thing sings!

This guitar is a prototype and there will be others similar, but this is a one of a kind that future axes may be built from some of the specs.

This guitar is 48 inches long and weighs 8.2 lb. Comes with kinsman HFB6 case. Remember, save a tree and buy from builders recovering hard woods. This guitar is in “Norway”.