1 300 kr
![MOFI ULTRA LOW NOISE FEET – DEMPEFØTTER FOR BEDRE LYD](https://images.finncdn.no/dynamic/480x480c//2023/12/vertical-0/17/1/333/005/731_1279836541.jpg)
Type: Platespillere
Topp modellen fra Victor på slutten av. 70 tallet . Ua 77 Tonearm og en Victor z1 pickup følger spilleren. Den veier 17 kg og foretrekker at den blir hentet. Spilleren har et lite hakk i plinth
2 stk støvlokk.
Alle kondensatorer og transistorer er skiftet.
Strobelys pæren må skiftes
This player system combines the JL-77 series, which were sold separately.
JL-T77 has been adopted for the turntable.
The JL-T77 uses a 20-pole, 60-slot, 6-phase DC direct drive motor for its drive motor. It uses a contactless Hall element servo and Victor's unique sine wave drive system to enable quiet rotation.
In addition, the turntable is finished with a die-cast aluminum alloy turntable with careful dynamic balance one by one, and the rubber covering is finished into a unique shape of a mortar with consideration of adhesion to both turntable and record.
UA-77 is used for the tone arm.
In addition to the static balance type arm, this arm is equipped with a TH (Tracing Hold) system that provides better tracing capability. In this system, the center of gravity of the movable part of the arm is lowered by shifting the weight of the main weight downward, and it has a restoring force similar to that of a arrowhead. This allows the arm to follow the warp of the record well and enables stable tracing of the needle tip.
In addition, the pipe arm is filled with anti-vibration material to achieve non-coevolution.
It uses a thread suspension type anti-skating mechanism, an oil dump type arm lifter, and a low-dose output cord.
The head shell is made of lightweight and highly rigid aluminum alloy impact press.
JL-C77 is used for the cabinet.
JL-C77 has a laminated structure consisting of high-density beech wood bonded with special vinyl adhesive to a thickness of 60 mm. The motor and arm parts are hollowed out to control internal vibration as well as external vibration.
A 7 mm thick aluminum alloy plate is used for the pickup board part to reduce vibration.
This board can be attached and detached, and the arm can be exchanged for each board by using a spare sold separately.
Thick acrylic dust cover is used to suppress howling.
The dust cover has a free hinge that allows it to be held at any angle, and the hinge is attached to the cover so that when it is removed and used, it leaves no obstructions in the rear.
A special rubber isolator with adjustable height is used for the leg part.
Type Record player
Turntable Section (JL-T77)
Motor 20-pole hole servo motor
Drive system Direct drive system
Turntable 31 cm Aluminum Die Cast
Number of revolutions 33 1/3, 45 rpm
Rotational speed fine adjustment range + / - 3%
Start-up characteristic Normal operation at 1/2 rotation
Wow flutter 0.03%WRMS
Signal-to-noise ratio 60dB
Tone Arm Unit (UA-77)
Arm type TH System Static Balance Type
Total Length 335mm
Effective arm length 245mm
Tracking error + / - 1 ° 30'
Overhang 15mm
Weight of mounting cartridge 10g ~ 32g (Including Head Shell)
Needle pressure variable range 0 ~ 3g
Cabinet Section (JL-C77)
Cabinet 60 mm thick beech
Dust cover Acrylic Free Hinge
Foot Height Adjustable
Pick-up board 7 mm Thick Aluminum Board
Pwer 100 VAC, 50Hz/60Hz
Power consumption 6W
External dimensions Width 490x Height 190x Depth 425 mm
Weight 17.0kg
Du må være logget inn for å se brukerprofiler og sende meldinger
InnloggingSist endret: 15.7.2024, 18:01 ・ FINN-kode: 360496069